Thoughts on Making Samples for Felt Garments

Thoughts on Making Samples for Felt Garments

After I wrote my previous blog on upsizing patterns for feltmaking, I thought I should write about how I figure out the shrinkage percentages to use when making the patterns bigger.   First of all, the samples I maker are really important to this process.  Not only do they help me figure out what colors and textures I want to use in the garment, but they also help me figure out the shrinkage. 

My biggest word of advice for sampling is to make it large enough to get an accurate measurement. I make a minimum of a 20 inch (50 cm) square sample using the types of textures, cloth and fiber I want to use in the final felt garment. For me, if I make anything smaller, the shrinkage is much more than if it is a larger piece. In the past when I did this, I ended up with something that was way too big. I don't always lay the fiber both directions in my garments, so I need to make my sample with the single layer. Also, I have found that if I am adding cloth to the surface and other surface embellishments, the shrinkage isn't as much as when I am just using a thin base cloth and the fiber layer. When I've done a garment that has both flat areas and large areas of texture, I make two samples, one just flat and one with the textures I think I'm going to use in the garment. Then I estimate how much textured area I'm going to have and how much flat area. If I'm just going to do a small amount of surface texture, I will use the shrinkage from the flat sample and it won't be affected too much. On the other hand, if I'm going to do a lot of surface texture with very little flat area, I use the shrinkage from the surface textured sample. But, if I am going to use about half flat and half with surface texture, I average the two different samples. Side Note: I am usually making a "sandwiched" felt textile in my garments. I put down a base of silk gauze, cover that with a thin, single layer of wool fiber and then put on the surface embellishments such as pleated or gathered bits of fabric, ribbon, yarns, pre-felts, fiber locks, etc.

There are many different versions of the formulas for figuring out the felt's shrinkage. People seem to have a hundred different ways to get to the same place.  My husband is a mathematician, so here are the formulas he helped me come up with: 

Formulas Needed for Making Your Pattern for a Felted Garment

So let's say I want to make a sample which is going to be simple, with no texture- just the ground cloth and the fiber on top of it. The sample will start out at 20 inches (50 cm) square but I will only lay the fiber in the vertical direction on top of the silk gauze ground.  After felting, the sample in the vertical direction is 13.5 inches (34.29 cm.)  In the opposite direction it's 17.5 inches (44.45 cm.) Since the fiber was only laid in one direction, it is not unusual that the shrinkages in the two directions would be so different. 

Figuring the Vertical Shrinkage Using my Husband's Formula:

A= 20 inches

B= 13.5 inches        

A-B  = 6.5

Divided by A = .325

Times 100 = 32.5%  (Which I would round up to 33%- I try to round up so there's a little extra for the "just in case" factor.)

Figuring the Horizontal Shrinkage: 

A= 20 inches

B= 17.5 inches

A-B= 2.5

Divided by A=.125

Times 100= 12.5% (Rounded up to 13%)

Now you have to figure out the size you will need to make your template so that the felt made from it will shrink down to the size you want.  As stated in my previous blog entry, I have already made a paper pattern either from an existing garment or from a sewing pattern.  If I am doing a seamless garment, I will usually work with just the back back piece as I've mentioned in the previous post.  I measure the widest and tallest part of the pattern. I use these measurements to figure out how much bigger the template pattern needs to be before shrinkage. 

Figuring the Pattern Size Before Shrinkage

Vertical Size

C= .33

D (Desired Finished Vertical Dimension of Garment Back) = 28 inches 

D divided by 1-C

28 divided by .67= 41.79 inches (rounded up to 42 inches)

So the beginning vertical size of the template is 42 inches.  Yes, this seems large, but that is why you need so much table space to make a garment! 

Horizontal Size 

C= .13

D (Desired Finished Horizontal Dimension of Garment Back) = 22 inches

D divided by 1-C

22 divided by .87= 25.287 inches (rounded up to 26 inches) 

The horizontal part of the template is only 26 inches wide because there is so much less shrinkage in this direction.  Remember, the fiber is being laid out vertically.  

The original paper pattern would have to be increased in the height and width to allow for the shrinkage calculated above.  To do this, I usually take the desired size and subtract it from the size before shrinkage.  

For the Vertical calculations above this would be  42 inches minus 28 inches. Which would be 14 inches.  I would slice my pattern up and separate it, spreading the 14 inches I need to add in small increments across the whole thing.  Since 14 divides nicely by 7, I would probably make 7 slices and spread each one 2 inches apart to take up the 14 inches. 

The Horizontal calculations would be 26 - 22, which would be 4 inches.  To spread this out, I would probably make 4 slices and spread each one apart by 1 inch.  

I try to be very careful in the shoulders, armholes and neck line to remember to include enough slices that they will not be too small, but also to not get them too big.  This can be tricky, so I often try to allow for the possibility that they won't fit exactly.  If they are a little too large, you can thread a strong, thin cord through the middle of the felt in that area and tug it to slightly gather up the excess.  If there are any wrinkles, these can sometimes be smoothed away with a steam iron.  If the area is too small, you might be able to apply steam (such as from a tea kettle) and stretch out the area while it is still damp and hot from the steam. 

Thoughts on Making a Felt Vest

How I Approach Making a Felt Vest

Pat Spark  © 2015

There are many different ways to plan a felt garment.  I am a plus sized woman and to get something that I would actually wear that fits me, I prefer to do the following: 

1. I find a sewing pattern that I think would look good on me. Or I make a pattern by tracing off a garment that I have that fits me well and is made from a woven cloth since anything knit stretches too much to make a pattern for felt. I make sure to have a full pattern piece for the back and a piece for the left and right fronts. If the back pattern piece is placed on a fold, I just lay it on folded paper and cut out the full back pattern.  If the sides are straight, I usually tape the pattern pieces together at the side seam.  

A sample of a sewing pattern from Rosemary Eichorn I used to make the white felt vest below. She wrote a book on sewn mosaic vests and the patterns she used in the book were quite good for "art" vests.  (The Art of Fabric Collage: An Easy Introduction to Creative Sewing.

Unfortunately, her patterns are no longer made, but maybe you can find them on Ebay.  

2. I cut the pattern out of an old piece of cloth (from an old sheet) and baste it together to see how it fits. 

3. I make adjustments on the cloth pattern until it fits well.  I open up the cloth pattern and make paper versions of the adjusted cloth pieces.   I can then use these pattern pieces on felt yardage and cut out the pieces and sew them together. 

Or if I want to make a seamless garment I do the following: 

4. I make a 20 Inch (50 cm) square sample using the types of textures, cloth and fiber I want to use in the final felt garment.  I carefully take before and after measurements of this sample so I can figure out the shrinkage.  Since I often lay fiber in only one direction, the resulting shrinkage will be greater in that direction and the square becomes a rectangle. 

5. Now that I know the shrinkage in each direction, 

A. I slash the paper pattern vertically and spread the pieces apart to allow for the width wise shrinkage.  I tape this altered pattern to another piece of paper and cut around it.  

 

 

Vertical Slashes

 

B. Then I slash the new paper pattern horizontally and spread the pieces apart to get the height shrinkage allowance. These pieces are then backed with more paper to stabilize them.

Horizontal Slashes

I redraw the pattern, smoothing out the contours. 

6. If the pattern is a simple vest with straight or slightly curved sides, I can use the back pattern piece to make a template for the seamless garment. To do this, I just use the enlarged back piece and add to the pattern at the neck, arm holes and the bottom.  I do this so I have no chance of accidentally running over the edge with some fiber and hooking together the front and back at these places.  The two overlapping fronts will be done one at a time to connect onto the back.   

But usually, I want a more shaped garment so then I have another choice.  I make an enlarged template for each pattern piece. Then I lay out the fibers, textures, etc. using the templates as guides. I felt them down to size and sew them together.  (Or use the Embellisher - needle felting sewing machine - to attach them together.)  I usually extend the enlarged pattern pieces at the shoulder and the side seam so I can overlap the back piece and have an interesting felted edge.

7. I haven’t tried the technique some people use which is to make each of the enlarged pieces of felt but keep the seam edges unfelted.  When the pieces are at pre-felt stage, you can overlap the unfelted seams and felt them together.  Then continue to felt the whole garment.  This looks as though it would allow a more shaped look but still be felted together instead of sewn. 

NOTE: In the following photos, the back pattern piece was extended at the side seams, to overlap the front pieces, while the front shoulders were extended to overlap the back piece.  Complicated I know, but I do this to help break up the vertical line caused by a sewn seam. Also, I LOVE irregular felted edges and don’t necessarily like straight, cut edges.

“Roses, Ruffles and Ripples, Oh My!” Felt vest by Pat Spark, © 2013.
(Textures influenced by Vilte Kazlauskaite.)

Vest from the Front

Vest from the Back 

Side Seam, Back Piece is Extended to Overlap the Front

Shoulder Seam, Front Piece is Extended to Overlap the Back

Detail of Front